Show simple item record

dc.contributor.authorZakaria, Muhammad Syamil
dc.contributor.authorMustapha, Mazli
dc.contributor.authorAzmi, Azwan Iskandar
dc.contributor.authorAhmad, Azlan
dc.contributor.authorIsmail, Sikiru Oluwarotimi
dc.contributor.authorShuaib, Norshah Aizat
dc.date.accessioned2022-03-17T11:00:01Z
dc.date.available2022-03-17T11:00:01Z
dc.date.issued2022-03-02
dc.identifier.citationZakaria , M S , Mustapha , M , Azmi , A I , Ahmad , A , Ismail , S O & Shuaib , N A 2022 , ' Effects of submerged convective cooling on turning of AZ31 magnesium alloy: Tool temperature and wear improvements ' , International Journal of Advanced Manufacturing Technology , pp. 1-20 . https://doi.org/10.1007/s00170-022-08985-9
dc.identifier.issn0268-3768
dc.identifier.otherORCID: /0000-0003-1451-1736/work/110097087
dc.identifier.urihttp://hdl.handle.net/2299/25437
dc.description© 2022, The Author(s), under exclusive licence to Springer-Verlag London Ltd., part of Springer Nature. This is the accepted manuscript version of an article which has been published in final form at https://doi.org/10.1007/s00170-022-08985-9 ​​​​​​​
dc.description.abstractLow melting point and material adhesion are associated challenges of magnesium alloy, leading to extreme built-up edge (BUE) and built-up layer (BUL) formations during machining process. Dry machining is favorable for machining magnesium alloy. However, this strategy inflicts excessive adhesive wear on the cutting tool. Therefore, this current work focuses on application of an innovative cooling technique, known as submerged convective cooling (SCC) for the turning of AZ31 magnesium alloy. Prior to cutting experiment, a computational fluid dynamics (CFD) simulation was conducted to evaluate internal structure of cooling module. Based on the CFD simulation, a small inlet/outlet diameter of 3 mm significantly contributed to the reduction of the tool temperature, due to high heat transfer coefficient of cooling fluid in the SCC. From the experimental results obtained, it was evident that SCC at high cooling water flow rate of 130 mL/min effectively reduced the tool temperature, chip temperature, and tool-chip contact length by approximately 50, 8, and 28%, respectively. Consequently, it improved the surface roughness by 37%, when compared with the dry cutting condition. Finally, both BUE and BUL were observed in dry and SCC conditions, but the severity of these wear mechanisms improved or decreased remarkably under SCC conditions.en
dc.format.extent20
dc.format.extent1615159
dc.language.isoeng
dc.relation.ispartofInternational Journal of Advanced Manufacturing Technology
dc.subjectInternal cooling
dc.subjectMachinability
dc.subjectMagnesium alloy
dc.subjectTool temperature
dc.subjectWear
dc.subjectControl and Systems Engineering
dc.subjectSoftware
dc.subjectMechanical Engineering
dc.subjectComputer Science Applications
dc.subjectIndustrial and Manufacturing Engineering
dc.titleEffects of submerged convective cooling on turning of AZ31 magnesium alloy: Tool temperature and wear improvementsen
dc.contributor.institutionCentre for Future Societies Research
dc.contributor.institutionCentre for Climate Change Research (C3R)
dc.contributor.institutionDepartment of Engineering and Technology
dc.contributor.institutionSchool of Physics, Engineering & Computer Science
dc.contributor.institutionMaterials and Structures
dc.contributor.institutionCentre for Engineering Research
dc.contributor.institutionDepartment of Pharmacy, Pharmacology and Postgraduate Medicine
dc.description.statusPeer reviewed
dc.date.embargoedUntil2023-03-02
dc.identifier.urlhttp://www.scopus.com/inward/record.url?scp=85125519910&partnerID=8YFLogxK
rioxxterms.versionofrecord10.1007/s00170-022-08985-9
rioxxterms.typeJournal Article/Review
herts.preservation.rarelyaccessedtrue


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record